Vehicle Wiring Details for your
2007-2011 Toyota FJ Cruiser Wiring Diagram | Printer Friendly
Version |  | | Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2007-2011 Toyota FJ Cruiser . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
| | |  | | PART | COLOR | LOCATION | | 12 VOLT CONSTANT | BLUE/BLACK (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 7 | | STARTER | GREEN/BLACK (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 8 | | STARTER 2 | BLACK/WHITE (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 1 | | IGNITION 1 | BLACK/RED (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 6 | | IGNITION 2 | BLUE/YELLOW (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 4 | | IGNITION 3 | N/A | | | ACCESSORY/HEATER BLOWER 1 | WHITE/GREEN (+) | @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 3 | | ACCESSORY/HEATER BLOWER 2 | N/A | | | KEYSENSE | N/A | | | PARKING LIGHTS ( - ) | GREEN (-) | @ HEADLIGHT Switch or BECU, (TOP, WHITE, 26-Pin Plug) Pin 8, NOTE #2 | | PARKING LIGHTS ( + ) | GREEN (+) | @ DASH FUSE BOX, (WHITE, 16-Pin Plug(F) Pin 13 | | POWER LOCK | GREEN/BLACK (TYPE B), NOTE #3 | IN DRIVERS KICK PANEL, (WHITE, 18-Pin Plug), Pin 4 | | POWER UNLOCK | GREEN/WHITE to BLUE/ORANGE (TYPE B),(Requires Double Pulse), NOTE #4 | IN DRIVERS KICK PANEL, (WHITE, 18-Pin Plug), Pin 5 | | DOOR TRIGGER | PURPLE/YELLOW (-) | @ BODY ECU, (TOP, WHITE, 26-Pin Plug) Pin 12, NOTE #5 | | DOMELIGHT SUPERVISION | WHITE (-) | @ DASH FUSE BOX, (WHITE, 20-Pin Plug(A) Pin 8 | | TRUNK RELEASE | BLUE/YELLOW (5-WIRE) #775 Relay Required | @ MOTOR IN REAR DOOR | | SLIDING POWER DOOR | N/A | | | HORN | GREEN/RED (-) | @ HORN Switch (BLACK, 12-Pin Plug) Pin 6 | | TACH | BLACK/WHITE (AC) | @ DATA Link Connector, (WHITE, 16-Pin Plug) Pin 9 | | WAIT TO START LIGHT | N/A | | | BRAKE | GREEN/YELLOW (+) | @ BRAKE SWITCH or DASH FUSE BOX, (WHITE, 16-Pin Plug(F), Pin 16 | | FACTORY ALARM DISARM | PINK (-) (Requires Double Pulse) NOTE #6 | IN DRIVERS KICK PANEL, (WHITE, 18-Pin Plug), Pin 8 | | ANTI-THEFT | TOYOTA'S TRANSPONDER SYSTEM, See NOTE #1 | @ IGNITION SWITCH TUMBLER | | EXTRA INFORMATION | | NOTE #1: TOYOTA'S TRANSPONDER SYSTEM, Requires Bypass Module: (For Remote Starting Only) Part #791 Bypass, (Requires Extra Key) for Operation. (For Remote Starting Only) Part # PK-ALL Bypass. (No Extra Key Required for Operation) 2-KEYS Required to Program Module. To order please go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS MODULE Page on this website. NOTE #2: the BECU (Body Electronic Control Unit) is connected tot he back of the FUSE BOX under the DRIVERS SIDE of the DASH. This Unit has (3) Harness connectors on the RIGHT Side of the FUSE BOX. NOTE #3: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Arm wire. NOTE #4: this wire is only needed if the Door Locks do not function with the Aftermarket System while the vehicle is running. All other times just use the Factory Alarm Disarm wire. NOTE #5: the BODY ECU is attached to the Back of the DASH FUSE BOX, it has 3 Plugs on the Right side Edge. NOTE #6: TEST this wire while turning the Key in the Drivers Door. This wire will also Unlock the Doors | | | | | |
0 Response to "Disney Princess Toyota Fj Cruiser Wiring Diagram"
ارسال یک نظر